Material Safety Data Sheet  is one document used by lipo battery manufacturers and importers to clarify the physical and chemical properties of chemicals (such as pH, flash point, flammability, reactivity, etc.) and the hazards to users’ health (such as carcinogenicity, teratogenicity, etc.).

The main information about MSDS as below:


1⃣️Id of the substance/preparation And the company

Product Identifier

Product name: Lithium Ion Polymer Battery Model: Liter 452050

Other means of identification

Synonyms: none

Recommended use of the chemical and restrictions on use

Recommended Use: Used in portable electronic equipment; Uses advised against: a)Do not dismantle, open or shred secondary cells or batteries. b)Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight. c)Do not short-circuit a cell or a battery. Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be shore-circuited by other metal objects. d)Do not remove a Lithium-Ion Polymer cell or battery from its original packaging until required for use. e)Do not subject cells or batteries to mechanical shock. f)In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If the contact has been made, wash the affected area with copious amounts of water and seek medical advice. g)Do not use any charge other than that specifically provided for use with the equipment. h)Observe the plus(+) and minus(-)marks on the cell, battery, and equipment and ensure correct use. i)Do not use any cell or battery which is not designed for use with equipment. j)Do not mix cells of different manufacture, capacity, size or type within a device. k)Lithium-Ion Polymer Battery usage by children should be supervised. I)Seek medical advice immediately if a cell or a battery has been swallowed. m)Always purchase the battery recommended by the device manufacturer for the equipment. n)Keep cells and batteries clean and dry. o)Wipe the cell or battery terminals with a clean dry cloth if they become dirty. p)Secondary cells and batteries need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions. q)Do not leave a Lithium-Ion Polymer battery on a prolonged charge when not in use. r)After extended periods of storage, it may be necessary to charge the discharge of the cells or batteries several times to obtain maximum performance. s)Retain the original product literature for future reference. t)Use only the cell or battery in the application for which it was intended. u)When possible, remove the Lithium-Ion Polymer battery from the equipment when not in use. v)Dispose of properly.

2⃣️Hazards Identification


No harm at the normal use. If contact the Eletrolyte liquid in the Li ion polymer Battery, reference as follows: Classification of the subsrance or mixture Classification according to GHS Acute Toxicity, Oral(Hazard category 4) Acute Toxicity, Dermal(Hazard category 3) Skin, irritate(Cagegory 1B) Eye Irrtate(Hazard category 1)

Precautionary statements:

Prevention: P263 Wash thoroughly after handling. P270 Do not eat, drink or smoke when using this product. P280 Wear protective gloves/protective clothing/eye protection/face protection. Response: P312: Call a Poison center or doctor/physician if you feel unwell. P302+P350-IF ON SKIN: Gently wash with plenty of soap and water P301+P330+P331-IF SWALLOWED: rise mouth. DO NOT induce vomiting. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

3⃣️Composition/information on ingerdients

Chemical characterization: Mixtures


Product: Consisting of the following components.

4⃣️Fire-fighting measures

Suitable Extinguishing Media

CO2, dry chemical powder, water spray.

Specific Hazards Arising from the Chemical

Formation of toxic gases is possible during heating or in case of fire. In case of fire, the following can be released: Carbon monoxide(CO) Carbon dioxide Other irritating and toxic gases.

Hazardous Combustion Products

Carbon oxides. Explosion Data Sensitivity to Mechanical Impact No Sensitivity to Static Discharge No

Protective Equipment and Precautions for Firefighters

As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH(approved or equivalent)and full protective gear. For example: Wear self-contained respiratory protective device. Wear suitable protective clothing and eye/face protection.

Special hazards arising from the substance or mixture:

Lithium Ion Polymer Battery may burst and release hazards decomposition products when exposed to a fire situation. Lithium ion polymer batteries contain flammable electrolyte that may vent, ignite and produce sparks when subjected to high temperature(>150°C), When damaged or abused(e.g. mechanical damage or electrical overcharging); may burn rapidly with flare-burning effect; may ignite other batteries in clothes proximity.

5⃣️First-aid measures

First-aid measures:

Eye Contact Rinse thoroughly with plenty of water, also under the eyelids. If symptoms persist, call a physician. Skin Contact Remove contaminated clothing and shoes. Wash skin with soap and water. In the case of skin irritation or allergic reactions see a phasician. Inhalation Move to fresh air. If symptoms persist, call a physician. Ingestion Do NOT induce vomiting. Drink plenty of water. If symptoms persist, call a physician. Most important symptoms and effects, both acute and delayed Swallowing Do not induce vomiting. Get medical attention.

6⃣️Accidental release measures

Personal precautions, protective equipment and emergency procedures

Personal Precautions Avoid contact with eyes. Refer to section 8 for personal protective equipment. Ensure adequate ventilation. Remove all sources of ignition. Evacuate personnel to safe areas.

Environmental precautions

Absorb with liquid-binding material(sand, diatomite, acid binders, universal binders, sawdust).

Methods and material for containment and cleaning up

Methods for containment Prevent further leakage or spillage if safe to do so. Methods for cleaning up Use personal protective equipment. Dam up. Cover liquid spill with sand, earth or other Non combustible absorbent material. Pick up and transfer to properly labeled containers. Clean contaminated surface thoroughly.

7⃣️Handling and stirage

Precautions for safe handling

Handle in accordance with good industrial hygiene and safety practice. Avoid contact with skin, eyes and clothing. Wear personal protective equipment. Was thoroughly after handling. Use this material with adequate ventilation. The product is not explosive.

Conditions for safe storage, including and incompatibilities.

If the lithium ion polymer Battery is subject to storage for such a long term as more than 3 months, it is recommended to recharge the Lithium-ion Polymer Battery periodically. 3 months: -10°C~+40°C, 45 to 85%RH. And recommended at 0°C~+35°C for long period storage. The capacity recovery rate in the delivery state(50% capacity of fully charged)after storage is assumed to be 80% or more. The voltage for a long time storage shall be 3.8V~4.8V range. Do not storage Lithium-ion Battery haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects. Keep out of reach of children. Do not expose Lithium-ion Polymer Battery to heat or fire. Avoid storage in direct sunligh. Do not store together with oxidizing and acidic materials. Keep ignition sources away—Do not smoke. Store in cool, dry and well-ventilated place.

8⃣️Exposure controls and personal protaction

Instrument Parameters

Ingredients with limit values that require monitoring at the workplace 12190-79-3 Lithium Cobalt Oxide TLV (USA): 0.02mg/m3 MAK (Germany): 0.1mg/m3 Vacated limits revoked by the court of appeals decision in AFL-CIO OSHS 965 F.2d 962 (11th Cir., 1992)

Individual protection measures, such as personal protective equipment

Eye/Face Protection Body protection Skin protection Respiratory Protection Hygiene Measures

9⃣️Physical and chemical properties

1⃣️0⃣️Stability and reactivity


Stable under recommended storage and handling conditions

Chemical stability

Stable under normal conditions of use, storage and transport

Thermal decomposition/conditions to be avoided

No decomposition if used according to specifications

Possibility of Hazardous Reactions

None under normal processing

Hazardous Polymerization

Hazardous polymerization dose not occur

Conditions to avoid

Strong heating, fire, Incompatible materials

Incompatible materials

Strong oxidizing agents. Strong acids. Base metals

Hazardous Decomposition Products

Carbon oxides, other irritating and toxic gases

1⃣️1⃣️Toxicological information

Acute toxiciy

No data available.

Skin corrosion/irritation

No irritant effect.

Serious eye damage/irritation

Cause serious eye irritation

Respiratory or skin sensitization:

No sensitizing effects known.

Specific target organ system toxicity

No information available

CMR effects(carcinogenity, mutagencity and toxicity for reproduction)

No information available

1⃣️2⃣️Ecological information


No data available

Skin corrosion/irritation

No irritant effect

Persistence and degradability

No information available

Bioaccumulative potential

No further relevant information available

Mobility in soil

No further relevant information available. Results of PBT and vPvB assessment PBT: Not applicable vPvB: Not applicable

Other adverse effects

No information available

1⃣️3⃣️Disposal considerations

Waste treatment methods

Recommendation: Must not be disposed together with household garbage Do not allow product to reach the sewage system

Uncleaned packaging

Recommendation: Disposal must be made according to official to official regulations.

1⃣️4⃣️Transport information

Transport information

The Lithium Ion Polymer Battery had been tested according to the requirements of the UN manual of tests and Criteria. The Lithium Ion Polymer Battery with a Watt-hour rating not exceeding 100Wh or the cell with a Watt-hour rating in not exceeding of 20Wh. The packaging shall be adequate to avoid mechanical damage during transport, handling and stacking. The materials and pack design shall be chosen so as to prevent the development of unintentional electrical conduction, corrosion of the terminals and ingress of moisture. Meets requirements of International Maritime Dangerous Goods(IMDG)-2014 Special Provision 188 to be transported as non-dangerous goods; Meets the requirements of 49CFR173.185 to be transported as non-dangerous goods for road, rail, air, and vessel. Meets the requirements of TDG special provision 34 to be transported as non-dangerous goods. The package must be handled with care and that a flammability hazard exists if the package is damaged.

1⃣️5⃣️Regulatory information

Safety, health and environmental regulations/legislation specific to the substance or mixture

Preview of MSDS test report